The Protolis guide to compression molding

Technical support for compression molding

• Best design pratices for compression molding

Compression molding, like other manufacturing methods, has to strike a balance between quality and cost-effectiveness. This section outlines some essential practices to optimize designs for compression molding in a way that combines lower costs with high-quality results.

5 best practices for compression molded parts

Effective design for manufacturability (DFM) ensures that compression molded parts are not only easier to produce but also cost-effective and efficient in terms of production speed. Here are five best practices to consider when designing for compression molding:

Optimize wall thickness

Design parts with moderate wall thickness (1.3-25 mm or 0.051-0.98 inches) to balance material usage and cooling times. Thinner walls use less material and cool faster, reducing overall production costs.

Minimize undercuts

While compression molding can accommodate recessed features, designs should minimize undercuts. Undercuts may necessitate complex ejection mechanisms like sliders, increasing tooling expenses.

Smooth transitions

Avoid sharp corners and abrupt changes in wall thickness to ensure smooth material flow and uniform cooling. This helps in maintaining the structural integrity and aesthetic quality of the part.

Strategic parting line placement

Place parting lines thoughtfully to minimize their visibility, particularly in flash molds. Consider the impact of witness lines and flashes on the part’s appearance, even if it is not a cosmetic component.

Utilize suitable draft angles

Incorporate appropriate draft angles to facilitate easy part removal from the mold, reducing the risk of damage during ejection and improving the efficiency of the molding process.

At Protolis, we extend DFM guidance to our clients, ensuring their designs are optimized for compression molding. Our expertise helps in refining product designs to enhance manufacturability, driving down costs and speeding up time-to-market for all compression molded parts.

• Understanding rubber compression molding tolerances

Navigating the tolerances in rubber compression molding is essential for achieving the desired product quality. The Association for Rubber Products Manufacturers (ARPM) classifies these tolerances into four tiers, from high precision to basic levels, facilitating appropriate selection based on product requirements:

• A1 – High Precision: This is the most stringent tolerance level, used for high-precision applications. It necessitates costly molds, fewer cavities per mold, and rigorous inspection and control measures.
• A2 – Precision: Less stringent than A1, this level still ensures precision. It requires detailed inspection, though the methods are less complex than those needed for A1.
• A3 – Commercial: This is a commonly used tolerance for commercial products where standard precision suffices for functionality and performance.
• A4 – Basic: The least strict tier, A4, is used where some dimensional control is necessary but cost constraints are significant.

Tolerances are categorized further into fixed and closed dimensions.

• Fixed dimensions are those that remain constant, machined into the top or bottom of the mold (without a parting line). 

• Closed dimensions are formed when the mold halves meet (with a parting line).

Tolerance tables in imperial (in) and metric (mm)

Nominal Dimension (in)	A1 Fixed	A1 Closure	A2 Fixed	A2 Closure	A3 Fixed	A3 Closure	A4 Fixed	A4 Closure
0 – 0.4	0.004	0.005	0.006	0.008	0.008	0.013	0.013	0.032
0.4 – 0.63	0.005	0.006	0.008	0.010	0.010	0.016	0.016	0.036
0.63 – 1	0.006	0.006	0.010	0.013	0.013	0.020	0.020	0.040
1 – 1.6	0.008	0.010	0.013	0.016	0.016	0.025	0.025	0.045
1.6 – 2.5	0.010	0.013	0.016	0.020	0.020	0.032	0.032	0.050
2.5 – 4	0.013	0.016	0.020	0.025	0.025	0.040	0.040	0.056
4 – 6.3	0.016	0.020	0.025	0.032	0.032	0.050	0.050	0.063
6.3 – over			x .004	x .005	x .005	x .008	x .008	x .010

Nominal Dimension (mm)	A1 Fixed	A1 Closure	A2 Fixed	A2 Closure	A3 Fixed	A3 Closure	A4 Fixed	A4 Closure
0 – 10	0.1	0.13	0.16	0.2	0.2	0.32	0.32	0.8
10 – 16	0.13	0.16	0.2	0.25	0.25	0.4	0.4	0.9
16 – 25	0.16	0.2	0.2	0.32	0.32	0.5	0.5	1
25 – 40	0.2	0.25	0.32	0.4	0.4	0.63	0.63	1.12
40 – 63	0.25	0.32	0.4	0.5	0.5	0.8	0.8	1.25
63 – 100	0.32	0.4	0.5	0.63	0.63	1	1.1	1.4
100 – 160	0.4	0.5	0.63	0.8	0.8	1.25	1.25	1.6
160 – over			x .004	x .005	x .005	x .005	x .008	x .010

Selecting the right tolerance tier is crucial for balancing product performance with manufacturing efficiency and cost. At Protolis, we are able to meet all these tolerance levels with extreme precision, ensuring high-quality products tailored to the specific needs of our clients.

• Possible finishes for compression molded rubber parts

The surface finish of compression molded rubber and silicone parts is crucial for their performance and longevity.

Factors influencing the surface finishing

1. Mold surface quality: The mold’s surface quality is crucial as it directly impacts the finish of the molded part. Different standards like SPI (Society of Plastics Industry) and VDI (Verein Deutscher Ingenieure) are used to specify the degree of polish. 

• SPI finishes range from A1 (high gloss) to D3 (rough textured), with varying degrees of smoothness achieved through different polishing methods like diamond buffing for high gloss and dry blasting for rough textures. 
• VDI finishes, on the other hand, use a numeric scale (e.g., VDI 12 to VDI 45), indicating the roughness from stone polishing to dry blasting.

2. Type of rubber: The rubber type affects the texture and quality of the surface finish. Different rubbers respond differently to the finishing process, with some achieving smoother finishes than others. For instance, natural rubber can achieve very smooth finishes, while synthetic rubbers might require specific conditions for optimal results.
3. Amount of mold release agent: The quantity and type of mold release agent used can affect the surface finish. Too much agent can lead to a duller finish, while too little might cause the rubber to stick to the mold, making it difficult to achieve a smooth finish. Silicone-based agents are generally preferred for their effectiveness and minimal impact on the finish.
4. Deflashing: The method used to remove excess material, or flash, from the molded part also affects the surface finish. Techniques like trimming or grinding need to be finely controlled to avoid surface damage, which can detract from the appearance and functionality of the part.

Each of these factors must be carefully managed to ensure that the molded rubber parts meet the required specifications for functionality and appearance. Selecting the right combination of mold quality, rubber type, release agent, and flash removal technique is crucial for achieving the desired outcome.

Surface finish classifications for compression molded rubber parts

The Association for Rubber Products Manufacturers (ARPM) classifies surface finishes into four categories:

• F1: This is the highest quality finish, providing a smooth, polished surface without imperfections. It is achieved using highly polished steel molds. The tightest tolerances are applied for critical dimensions, and visual defects like parting lines, flow marks, and flash are almost entirely eliminated.
• F2: It allows for very small, unpolished tool marks. It offers a polished finish but is less meticulous than F1. Some visible parting lines and slight flash might be present, but they do not affect the functionality of the part. Commonly used in automotive seals, gaskets, and industrial components where a clean appearance and reliable performance are important but not at the same stringent level as Class A.
• F3: Known as a “commercial finish,” larger parting lines, flash, and minor surface imperfections are allowed, as long as they don’t compromise the performance or function of the part. Suitable for commercial applications where the primary concern is functionality rather than aesthetics, such as rubber mounts, bushings, and gaskets used in non-visible areas
• F4: Lowest quality finish where cosmetic appearance is not a priority. Significant flash, parting lines, and surface irregularities are permissible as long as they don’t affect the part’s performance

Generally, F3 is sufficient for many applications unless a smoother surface is critical for the product’s function or appearance. Choosing a finer finish like F1 or F2 will increase mold costs due to the higher level of precision required in the mold’s surface.

Possible surface finishing methods

Here are several finishing methods for compression molded rubber parts, each tailored to enhance the properties and performance of the final product:

• Fluorination: This process involves exposing the rubber part to a fluorine gas mixture in order to modify the surface properties. This modification makes the rubber more resistant to weather, temperature, and certain chemicals like solvents. The alteration is only surface-deep, preserving the core properties of the material.
• Low friction coating: Various coatings are applied to reduce friction and enhance wear resistance. The coatings can be selectively applied to specific areas, enhancing flexibility in manufacturing.
• Flocking: This technique uses man-made fibers, aligning them electrostatically on an adhesive layer. Flocked surfaces reduce friction, noise, and dirt accumulation, and improve moisture regulation, sealing, and electrical insulation. Flocking can be applied partially by masking non-target areas during the adhesive application.

Each of these methods is selected based on the specific requirements of the application. At Protolis, we offer various finishing options for our rubber compression molded parts. Our primary focus is improving our rubber components’ functionality, appearance, and performance.

See all the finishings that you can get in Protolis.

• Cost optimisations for compression molding

Various factors influence the cost of compression molding projects. Understanding these factors is vital to managing expenses, so let’s take a closer look.

Continue your exploration of compression molding in other chapters.